New member with question

  • 340 Views
  • Last Post 02 May 2020
  • Topic Is Solved
sluggo posted this 29 April 2020

Hello: I am new to the forum. Sorry if this is a repeat question. I was unable to see if my question was asked before. I have reloaded cast bullets for handguns for years. I want to start using cast bullets in my Krag rifle and my 03A3 Springfield. As a general rule should I load so the bullets just touch the rifling or keep them back a little? These loads will be for target use. Thanks, sluggo

Attached Files

Order By: Standard | Newest | Votes
R. Dupraz posted this 29 April 2020

It depends on what the rifle likes. Some shoot best when the bullet is touching. Some don't. I have two 98 Mausers and a 1903 Springfield that I use for the military  matches. all of them shoot the smallest groups when the bullet does not touch the leade.

There is no set rule. Starting out with a "new to cast  rifle", initially I seat the cast bullet off the rifling  and then experiment with the OAL from there. Just one of the many variables that you have to experiment with to find out what your rifle likes best.   

 

R

Attached Files

sluggo posted this 29 April 2020

Thank you. This is not usually a factor in handgun loading. I have a starting point for my rifles now.

Attached Files

beagle6 posted this 30 April 2020

I can't help you with the 03A3 but my friends and I shoot Krags in informal matches. It seems that the preferred bullet size is .311 and heavier bullets ( above 150 grains ) shoot best. We keep them off the rifling but the rifle will decide how much. Mine likes around 1/32 of an inch.

beagle6

Attached Files

  • Liked by
  • Bud Hyett
sluggo posted this 30 April 2020

Thanks. I have 2 molds that I can size to .311 for the krag. A 200 grain and a 220 grain. They both use gas checks but I plan on keeping the velocity around 1600 to 1800 fps. I will start with your suggestion and keep the bullet off the leade. Thanks again.

Attached Files

John Alexander posted this 30 April 2020

I am confused by the answers given in this thread and could use some help in understanding.

By far the most popular bullet used in 03A3's in CBA military matches is the xxx299 which is a bore riding nose bullet.  When I shoot that style of bullet best results are with the nose of the bullet not only touching the touching the lead but being well past the leade and into the bore and being slightly engrave by it.

Are we saying that the front driving band doesn't touch the leade or talking about a different bullet design? I may be the only one confused (it has happened before) but I doubt it.

Help.

John

Attached Files

  • Liked by
  • Bud Hyett
beagle6 posted this 30 April 2020

John

I have no experience with 03's. In my Krag, I use a 180 gr. bullet intended for 303 British. Comes out of the mold at .314 and I size it to .311. The nose portion mikes at .303 -.304. You cannot start the nose of the bullet into the muzzle and a long loaded cartridge will definitely show marks from the rifling. I don't shoot in the CBA Military Matches but my system is plenty good enough for my informal matches. Hope this clears up any confusion.

beagle6

Attached Files

RicinYakima posted this 30 April 2020

"Are we saying that the front driving band doesn't touch the leade or talking about a different bullet design?"

As many know I prefer the 311284 over the xxx299. With issue or worn throats, it is very hard to get the first drive band into the leade with the '299 and keep the bullet in the neck of the cartridge. I start with the '284 nose resting on the top of the lands and the first drive band touching the foreword end of the leade. Running tests as I work out OAL depending upon what that rifle shoots best.

Attached Files

  • Liked by
  • Bud Hyett
Wheel Weights posted this 01 May 2020

Back in the day, all the best shooters of single shots breech seated their bullets and used the same case over and over. A good friend who owns many Pope rifles still does it that way. 50% more accurate than fixed ammo.

IME when using bore rider bullets, best accuracy is when the bullet engages the rifling. NEI made many bore rider molds with what the called a "DD". It was a driving band designed to engage the rifling. I have three of those in 30, 35 & 40. All are very accurate. 40 caliber results in a No. 1 450-400. You can see the band on these wheelweight bullets lubed w/SPG.

 

Attached Files

John Alexander posted this 02 May 2020

"Back in the day, all the best shooters of single shots breech seated their bullets and used the same case over and over. A good friend who owns many Pope rifles still does it that way. 50% more accurate than fixed ammo."

===========

The CBA has a class for the Schuetzen (plain base breech seating) shooters and these shooters are still around. They are sometimes the biggest class at the CBA National Tournaments. Our two rifle classes allowing gunsmith built custom rifles, as with the plain base shooter rifles, display about equal accuracy.  In fact the national records for Heavy class (14 pound limit) and Unrestricted class using fixed ammunition are better than those for the plain base class doing breech seating in most categories.

The top rifles and shooters in all three classes are capable of Averaging about .5 MOA for four five shot groups at 100 yards.  Of course the records are much smaller than 0.5 MOA because the records are set by rare events not the true average capability of rifle and shooter.

Anybody who thinks that 0.5 MOA isn't  top shooting for cast bullets has been reading too much on the Internet.

John

 

 

Attached Files

  • Liked by
  • RicinYakima
  • MarkinEllensburg
sluggo posted this 02 May 2020

Hello: thanks for the replys. I am trying to post a picture of the bullet I am loading but I am having trouble doing so.

Attached Files

Close