I had a load for a British SMILE III of 27 grains of IMR 4227 for an 185 cast bullet from a RCBS mold that shot excellently in Ohio about 25 years ago. I shot the load in Colorado and the bullets go through the target sideways. I varied the power to IMR 4895 from 24.5 to 38.8 grains in .5 increments and all the bullets shot side ways. How do you slug the chamber and the barrel? The mold drops a bullet between .311 and .312, I do not size the bullet trying to get the largest bullet. The bullets are gassed checked. Any ideas. I am a new member and I hope that I have filled this out correctly. Any help would be appreciated.
303 british
- 1.5K Views
- Last Post 10 July 2020
If you need a .315" sizing die, Buffalo Arms sells them and other custom sizes. They are a bit pricey though.
https://www.buffaloarms.com/315-custom-lead-bullet-sizing-die-for-lyman-rcbs-lubrisizers-bac315
Ken
Attached Files
Tom at Accurate Molds will cut the mold to the exact size you want. He has a wide selection of 30 caliber designs to choose from and his turn around time is usually within two weeks. Accuratemolds.com.
Attached Files
Jim: Check the offerings at [email protected] Al has several moulds available for the fat thirty's. Gp
Attached Files
If you want a .315 sizing die, why don't you just buy a .314 and open it up .001". I did that with a stick, some crocus cloth and a stick. I went from .457" to .460", and they shot a whole lot better. The die worked just fine in my lyman 450.
B.E.Brickey
Attached Files
Erik does some great work but it would be cheaper just to purchase the correct size mould.
Cheers from New Zealand
Attached Files
Hollowpoint Mold can open up an existing mold to a larger diameter. I had this done once and it produced bullets just the size I wanted and I was using range scrap. Their website is hollowpointmold.com and Erik is the owner. His phone number is (541)738-2479, email is [email protected]. I forget the cost, but it is something like $30 per band on the bullet - that may be wrong. For example, you could open up a .313" bullet to .315"
My SMLE has a .313" bore, so I'm OK with a mold and sizer (Lyman '313") Lyman does make a .314 sizer die as does RCBS. Neither list a .315" die, but maybe RCBS can make one on special order.
Attached Files
Pleased to see you are getting on with it,I would like thank Ed Harris for his tip on slugging the throat with a 38 lead bullet,when I was casting a few days ago,I started with some scrap lead and cast a few RCBS round nose bullets,have only checked one barrel so far,it was 315+ a fraction.
Attached Files
All, I want to thank you all for taking the time to help me with my 303 problem. I really do appreciate all your comments. Here is where I am so far. I bought some gerrosafe and slugged the chamber, the throat and the barrel. I measured the length of the case, the length of the case throat and the length of the barrel throat. I have incorporated all those dimension and seated the bullet .001 from the rifling. I am trying to find a .316 diameter mold, a.315 sizer that will work with an RCBS lube-a-matic and a top punch that fits the mold, so far I have not had any success. I am looking for a bullet weight of 170 grains are so. I have changed my lead mixture from linotype to a two pounds of linotype with one pound of pure lead mixture trying to get a softer bullet that will expand and fill up the barrel. In order to help that, I have gone from IMR 4895 to IMR 4227 hoping to get a sharper bump behind the bullet. Any help or comments on finding a mold and sizer that would work with my RCBS handles and Lube-a-matic would be appreciated as well as any comments on my progress to date.
Attached Files
The 16gr of 2400,ar 2205 seems to work well my own experience is if that don’t work nothing will
Attached Files
1. slug the bore
2. cerrosafe cast the chamber and throat.
3. measure
4. you'll have your answers.
Attached Files
With all due respects to previous posters,there is more to this problem than bore and bullet diameter.At some stage undersized bullets will give trouble I know,however bad barrels,lubrication and over stressing bullets with too much propellant cause most of the trouble.I shot a RCBS 180 gr Spire point gc in a number of rifles,sized .312” and it was barely .312”.Unfortunately many 303 barrels are in a shocking condition,corrosive primers and incorrect or lack of cleaning will ruin a barrel very quickly.
Perhaps you may be able to find some different bullets,but in the meantime I would try some lighter loads,say 16 grains of 2400 or 17-18 grains of 4227.
Attached Files
I have stoped worrying about the bore , fill the throat the bullet will swage down
sounds like you need a fatter bullet I was fighting with under size bullets and work on .316” and have no worries in my smle s
Attached Files
Load the fattest bullet a spent case will hold if you can.
Cheers from New Zealand
Attached Files
Easy way to do pound cast of throat is to pull a 158-grain LRN .38 Special bullet from a factory load, drop it into the chamber neck, pound it into the neck and throat with a 3/8" brass rod until the rod stops against the shoulder cone, then tap out the slug to measure the neck and throat diameter.
73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia
Attached Files
Jim, Real Quick to slug the barrel : Grease barrel with vaseline or just oil it good, drive a soft lead slug down the length of the barrel from the muzzle. You can use a steel rod or a zinc one either is available at the hardware store, if using steel wrap some electricial tape around it in a spiral so the rod can't touch the bore. I use egg shaped fishing sinkers just a little larger than the barrel.
To make a pound cast: Fill an empty fired case (dead primer) with lead to the middle of the neck, place a soft lead bullet in the neck, chamber the case and pound the bullet down from the muzzle using that metal rod. DO NOT TRY TO USE A WOODEN ROD!! The soft bullet should upset and make a copy of the throat and maybe even a little of the rifling.
Good luck
B.E.Brickey
Attached Files
I assume you are talking about 2 different rifles. Most Enfields in my experience run .314 and up. .318 isn't unheard of..Slug your barrel. That most likely is your problem. There is all kinds of advise on how to do it so I won't bore you. Clean the barrel, oil lightly and use a SOFT lead slug. Sounds like you have a micrometer and know how too use it. Good luck.
beagle6
Attached Files
Categories
- All Categories
- General Polls
- Contact Us w/ Forum Issues
- Welcome to The Cast Bullet Association Forum
- General
- Bullet Casting
-
Guns and Shooting
- AR Platform
- TC Contenders & Other Single Shot Handguns
- Shotguns
- Informal Matches & Other Shooting Events
- Gunsmithing Tips
- Gun Cleaning & Maintenance
- Optics
- Benchrest Cast Bullet Shooting
- Military Bench Rest Cast Bullet Shooting
- Silhouette Shooting
- Postal Match Cast Bullet Shooting
- Factory Guns
- Black Powder Cartridge
- Hand Guns
- Lever Guns
- Single Shot Rifles
- Bolt Action Rifles
- Military Surplus Rifles
- Plinkers Hollow
- Muzzleloaders
- Hunting
- Reloading
- Buy, Sell or Trade
- Other Information & Reference
Search
This Weeks High Earners
- John Carlson 22
- Bud Hyett 21
- linoww 17
- MP1886 13
- MarkinEllensburg 10
- drone 9
- Aaron 7
- beltfed 6
- Lucky1 6
- Eutectic 6